Cth200 Cth2 216-1ad46-0X24, 1*Ethernet Port, 3*100kHz Pulse/Dir Motion Control Output or 2*20kHz Pto/PWM Output, Data Permanent Storage. Support RS485,

Product Description

 

Product Description

Order No.: CTH2 216-1AD46-0X24
Specification: H226IM:128KB program memory+64KB Secret library+64KB Secret library,64KB data memory+100KB extension V section,24VDC power supply,14DI/10DQ transistor output,0.5A ,2 PPI/FPORT port,1 Ethernet port,3*100KHZ motion control output(Pulse/Dir) or 2*20KHz (PTO/PWM).Data permanent stored.Support Analog,CAN and RS485 expansion boards,support S7 protocol.

 

Performance Parameters

Physical Features

Dimension(W×H×D)

137×80×62mm

Power consumption

7W

Program memory

128K+64K+64K

Data memory

64KB+100KB,Data permanent stored

Maximum number of expansion modules

7

Maximum digital

128DI/128DO(expand CAN expansion board up to 640DI/640DO)

Maximum analog

32AI/32AQ(expand CAN expansion board up to 194AI/194AO)

Data stored

FlashROM Data permanent stored

Power supply features

Rated input voltage

DC24V

Impulse current

28.8VDC,12A

Isolation (field and logic)

None

Hold time (power off)

10ms above

Sensor +24V power output

Voltage range:20.4~28.8VDC

Rated current:300mA

Maximum ripple noise (<10MHz) :<1V peak-to-peak value

Isolation (sensor and logic):Non

Power alarm

when it is lower than 15V, the alarm bit SM195.1

Regular features

Total timers

512

1ms

4

10ms

272

100ms

236

Counters

256

Accumulators

4

Memory bit

256bit

Local storage(L)

64 bytes independent

Sequence control relay(S)

256 bit

Time interrupt

2*1ms resolutions

Edge breaks

8

Boolean operation execution time

≤0.15us

Floating operation execution time

≤6.2us

Real time clock

Built-in

BD expansion board port

One ,BD expansion board supports RS485 expansion board, CAN expansion board, and analog expansion board

System indicator

SF indicator (red)

ON:Program error,OFF:Normal

DIAG indicator (orange)

ON:Program control,OFF:Normal

RUN indicator (green)

ON:running,OFF:stopped

STOP indicator (orange)

ON:stopped,OFF:running

RMC indicator (green)

ON:remote control is connected,OFF:remote control is disconnected

LNK/ACT indicator (green)

ON:Ethernet connection,Blinking: Transmission ,OFF:disconnect

Run switch

RUN/STOP

External battery port

Special battery card

Programming card

Support

Integrated communication capabilities (PPI/ free port)

Communication interface

2 Communication port: PORT0:PPI/free port,standard RS485 PORT1:PPI/free port,standard RS485 After the RS485 expansion board is plugged in and restarted, PORT0 (RS485, PPI communication port) PORT1 (RS485, PPI/ free port), FPORT0 (free port)

Baud rate(baud)

9.6k,19.2k and 187.5k

Free port baud rate(baud)

1.2k ~ 115.2k

Maximum number of stations

32 stations per segment, 126 stations per network

Maximum number of main stations

32

Point-to-point (PPI master mode)

Yes(NETR/NETW),With a maximum of 8 connections and a maximum communication of 200 bytes per connection

MPI connect

8(1PG/1OP),2 reserved

Maximum cable length per section      Use an isolated repeater      No isolated repeater is used

The baud rate is 1000 m at 187.5 K and 1200 m at 38.4 K 50m

Ethernet Communication

Communication port

1 Standard Ethernet port

Communication standards

IEEE802.3 standards

Transmission speed

10Mbps/100Mbps adaptive

Adaptive cross-connect

Support

Hardware interface

RJ45

Protocol Type

UDP/TCP protocol Supports UDP_PPI, MODBUS_TCP, Socket, and S7 protocols, Ethernet communication between PLCS, and MiCo Ethernet programming.

Configuration mode

Ethernet port search PLC,support the mouth download system configuration.

Maximum number of connections

8 UDP/PPI connections, no master or slave

8 TCP/Modbus connections, no master or slave

4 Socket connections, 2 UDP, 2 TCP

8 S7 protocol, no master and slave, COTRUST PLC only as slave station

Maximum single data transmission

Up to 200 bytes for UDP_PPI transmission.

Up to 240 bytes are used for ModBus_TCP transmission.

Up to 512 bytes is used for Socket  transmission

Up to 200 bytes for S7 transmission

Startup time of network port

5 to 10 seconds. The startup time varies depending on the network environment.

Indicator

RMC

On: The remote server is successfully connected

Off: The remote connection is disconnected or the remote function is disabled

LINK/ACT

On: The hardware of the network port is connected

Blinking: Data is being exchanged

Off: The hardware of the network port is disconnected

The length of the communication cable

100M,cable type is CAT5e or above

Isolation

Communication isolation

IP address reset  function

Five consecutive times within two seconds

Upgrade Firmware function

Use MagicWorks PLC and MiCo to remotely upgrade firmware from company servers over Ethernet

I/O Features

Number of integrated digital inputs

14

Input type

Leak/Source

Number of integrated digital outputs

10

Output type

Source

Maximum digital

128DI/128DO(expand CAN expansion board up to 640DI/640DO)

Maximum analog

32AI/32AQ(expand CAN expansion board up to 194AI/194AQ)

The maximum number of local expansion IO modules

7

Pulse capture input

14

High-speed counters

Total     Uniphase counters          AB-phase counters

6 6×50KHz 4×30KHz

Integrated Communication Function (CANopen) - use for CAN communication board model CTH2-CAN-01S2-EB

Communication Interface

1(8 Pin)

Communication speed(kbps)

1000

800

500

250

150

50

20

Maximum cable length(m)

25

50

100

250

500

1000

2500

Maximum station address

127

Station address range

1-127

Maximum number of master and slave stations

32

Configuration method

CAN configuration blocks and EDS files

Maximum digital access

Nomal IO

CANopen IO

Byte

Memory starting address

Byte

Memory starting address

Input

16

IB0

Input

64

IB16

Output

16

QB0

Output

64

QB16

Maximum analog access

Normal IO

CANopen IO

Channel

Memory starting address

Channel

Memory starting address

Input

32

AIW0

Input

162

AIW64

Output

32

AQW0

Output

162

AQW64

Integrated Communication Function (CANFree) - Used when extending the CAN communication board

Communication Protocol

CanFree

Use method

Supported by internal library instructions

Digital input features

Number of interated digital input

14

Input type

Leak/source

Rated voltage

24 VDC

Maximum continuous allowable voltage

30 VDC

Logic 1 signal (min.)

18 VDC,3.0mA

Logical 0 signal (Max.)

5 VDC,1mA

Isolation (field and logic) Isolation group

500 VAC,1min

Simultaneously connected input

14

Maximum cable length

500m

Shielding: 50 m (high speed counter input); Unshielded: 300 meters (standard input)

Digital Output Features

Number of integrated digital output

10

Output type

Solid-MOSFET,source

High speed pulse output

3*100KHz motion control output(Q0.0,Q0.1,Q0.2) 2*20KHz PTO/PWM output(Q0.0,Q0.1)

Output frequency (maximum)

100KHz(Q0.0-Q0.2),1KHz(Q0.3-Q1.7)

Rated voltage output

DC:24V

Output voltage range

20.4-28.8 VDC

Rated current per point

0.5A

Rated current for each common point

4A

Leakage current (maximum)

10µA

Surge current

8A,100ms

Lamp load (maximum)

5W

On resistance (contact)

typical 0.3Ω,the max 0.6Ω

Delay

Off to on:2us(Q0.0, Q0.1, Q0.2),15us

on to off:10us(Q0.0, Q0.1, Q0.2),130us

Output of simultaneously connected

10

Parallel output

Only when the outputs are in the same group

Maximum cable length

Shielde

500m

Unshielded

150m

 

CTH2 216-1AD46-0X24 wiring diagram

 

 

RS485 communication port definition

Connector	PIN	PORT0(RS485)	PORT1(RS485)
	1	Shell Grounded	Shell Grounded
	2	logically	logically
	3	RS485+signal B	RS485+signal B
	4	Send the application	Send the application
	5	+5V,Grounded	+5V,100ΩGrounded
	6	+5V 100Ω	+5V 100Ω
	7	+24V	+24V
	8	RS485-signal A	RS485-signal A
	9	NC	NC
	shell	Shell Grounded	Shell Grounded

 

RS485 expansion board communication interface

Module interface and connector	PIN	FPORT0(RS485)
Note:when terminal resistors are needed, short connect the 2 and 3 pins	1	RS485+signal B
	2	RS485-signalA
	3	Terminal resistance
	4	Shell Grounded
	5	RS485 signal GND
	6	NC
	7	NC
	8	NC
	9	NC

 

Company Profile

FAQ

Q1.What's the payment term? 
A. We accept TT,LC,Western Union,Paypal.

Q2.What is the delivery time?
A. It depends on order quantity,usually it will take about 3-5 days for sample production.

Q3.What's the package used for?
A. For the small capacity,will use carton,but for big capacity,we should use honeycomb carton and pallet or wooden case for protection.

Q4.Would you accept to use our logo?
A.It's no problem,we accept OEM service.

Q5.What's your production capacity for one month?
A. Our month capacity can reach near 500-3000pcs for the most of our model.

Q6.Where is your market?
A. Our products are popular in Australia,South America,Philippines,Italy, America, Pakistan and so on.Some of them are our regular customers and some of them are developing. We hope you can join us and make mutural benifit from our cooperation.

Q7. What kind of certificates you have?
A. Our company has ISO9001,CE, RoHS,SGS etc.
 

OEM Services
Logo
Please offer us your own high resolution logo in JPG format,there should be two colors at most in the logo and there should be no gradient effect in the logo.
2. Label
Please offer us your own model numbers.

Lead Time
1.Sample orders will be delivered from our factory within 3-5 working days.
2.General orders will be delivered from our factory within 7-15 working days.
3.Large orders will be delivered from our factory within 45 working days at most.

Shipment
1.By EMS,DHL,FedEx,TNT,UPS or other Express.
2.By our forwarding agent(by Air or by Sea).
3.By your own forwarding agent.